Progetti Archives - Trevisan Art Studio

Semplice Fasciatoio in Legno

March 15, 2019

Difficolta’:  1.5/5 Costo: circa 15Euro Attrezzi: Elettroutensili richiesti Tempo richiesto: 1,5 Giorni Questo è un lavoretto di bricolage molto semplice: un fasciatoio di legno che usa il materasso vädra dell’Ikea. Ho progettato questo fasciatoio per adattarsi sopra un lettino tipico, ma ovviamente va bene anche per tavoli, comodini o letti. L’idea iniziale era una semplice scatola aperta sul lato superiore, certamente qualcosa alla portata anche di principianti. Costruendo il fasciatoio I due lati lunghi

Simple Wood Changing Table

March 15, 2019

Difficulty:  1.5/5 Cost: about 15Euro Tools: Power tools recomended Time required: 1,5 Days This is a very simple bricolage project: a woodden changing table that uses Ikea’s vädra mattress. I designed this changing table to fit over a standard crib, but of course it can also work over tables, drawers or beds. The initial idea was a simple box open on the top, certainly something even beginners can build without much drama. Building the

A1-C End of Construction

July 17, 2018

For the first time in over 20 years, the plane is complete in all its parts! Even if during the last days there were lots of minor improvements and re-engeneering of a few areas, I managed to wrap it up. The main concern was to get the CG right, or as close as possible, without having to add ballast to center the model. In the design phase, I moved a lot of weight to the

A1-C Engine cowl

July 17, 2018

The engine, or in this case, motor cowl, has been first modeled from a solid block using sandpaper… glasses and a mask. Once happy with the shape, I started laminating the epoxy and fiberglass mats in various weights. For the epoxy I once again looked in the prochima line of products and ordered the E-227 resin. After the first sanding of the fiberglass (again, wear masks, glasses and gloves!) i covered the whole cowl with

A1-C The Project

May 14, 2018

The A1-C project was started in the last century. In the beginning I designed the airframe with my father for a small class .25 glow engine. Little we knew about aeronautical structure design, or even just model design. That’s why for the first prototype we took inspiration from the early 3D Fun Flyers, which started to appear on the market in the late nineties. While not so bad in the general design, it was way

PC/tray table

May 12, 2018

Teaching new tricks to old lamps (Part two)

January 11, 2018

Converting two old gate lights in balcony candle holders This is the second set of lamps we converted, to find out what we did with the first pair, check the part one. once again, not the cleanest lamps around As for the other pair, we had to use a lot of imagination to see through all those layers of dust and dirt, and give them a second life. Since we had already started the balcony

Teaching new tricks to old lamps (Part One)

December 29, 2017

From old wall lamps to cute led nightstand lights. This is a two-part story, because we actually took care of two sets of lamps, both found in the family storage few months ago. a dusty start… These dusty and oxidized brass wall appliques had a gloriuos past in the tavern of my grandparents house. For several years they witnessed every big family reunion, until they were no longer needed, the house eventually sold, and they

Renovating an old bike

December 29, 2017

It actually happens quite often in our family, to start a “simple little project”, and end up with a major overhaul. This old bike was lying all dusty and rusty at my parent’s house, and it seemed a nice and quick temporary way to provide us with some two-wheeled freedom in our new house. Of course, that idea was going to change very soon,